Pre-order - Studio Product & Reproduction Stand STA-C01-360
Pre-order: This product will be shipped when available
The STA C01-360 stand is designed for imaging applications that require more precise alignment in both the horizontal and vertical plane with respect to the subject matter. When reproducing artwork that is mounted or objects that cannot be disturbed or manipulated, it is important to be able to adjust the stand so it is aligned with the artwork or object, for true and accurate reproduction.
The overall height and width of this stand allow it to be moved through a standard doorway for use in another studio or lab. The hand-operated foot plungers are easily adjusted to provide alignment or compensation for uneven floor surfaces. When required, using the hand levers, rotate, and fully extend all three-foot plungers until the hand lever is firmly pressed against the top of the leg.
Check each of the three legs, using a level to determine which one of the three legs needs to be lowered to compensate for the floor. With the level placed on top of a leg, tilt the level to simulate lowering that leg to determine the end effect.
The STA C01-360 provides additional reinforcement of the Horizontal Arm/Bar by a newly designed heavy-duty interface plate. The plate provides two additional bolts, strategically located, one on each side of the vertical carriage, for a total of 4 bolts. This new design provides additional load support and spreads the load forces from the horizontal arm into both the front and the sides of the vertical carriage casting.
Optional Horizontal Arms are available for extending the working width of the STA C01-360 out to an approximate maximum of 1350mm / 54 inches (measured center of Vertical Column to the center of Camera plate). With an optional extended horizontal arm* the STA C01-360 is ideal for over table product imaging and ART work reproduction/cataloging. With fixed installation and large ART work reproduction applications, the STA C01-360 combined with the optional 01-350HB-1500 horizontal arm* provides 2700mm / 108 inches / 9 feet of total working width.
The STA C01-360 + optional horizontal arm* is an ideal solution for simplified workflow when stitching high-resolution images together. A unique STUDIO TITAN feature not found on other Studio Stands are the vertical and horizontal column graduated tape scales. The measuring scales provide a point of reference which allows the photographer to log and then quickly re-create a previous set-up. It also provides set-up reference points for stitch together applications.
The Camera Head Mount Plate is user adjustable and provides the following shooting positions: 0 degrees, pointing up as supplied, 90 degrees, 180 pointing down for tabletop photography, and 270 degrees.
*Before installation and use of an optional horizontal arm please read the STA_01-350HB_Horizontal_Arm_Bar_ manual. When using an optional horizontal arm, consideration for load reduction and using additional weights/sandbags on the legs of the base are required to prevent instability or a tip over.
Precision-manufactured with attention to detail using CNC machinery.
Smooth motion bearing on Z and Y columns with a secure axis lock.
Counterweight in center column allows single-handed operation.
Low center of gravity base with hand plungers and locking casters.
Premium Dual Stage bearing casters provide easy movement around the studio. The dual-stage foot brake stops both the wheel from rotating and the caster housing from swiveling, preventing unwanted movement.
Essential tools are included to complete assembly.
• Total Height : 203cm / 79.92 in
• Working Height Maximum : 176cm / 69.29 in (measured from Camera Plate to floor)
• Working Height Minimum : 61cm / 24 in (measured from Camera Plate to floor)
• Working Width Horizontal : 55cm / 21.6 in (center of Column to center of Camera plate)
• Width : 85cm / 33.46 in
• Weight : 40kg / 88lbs
• Suggested Wheels : 01-350-20-024
• Base Diameter :100cm / 39.3 in
• Recommended General load capacity : 10kg (22lbs)
• Camera Plate Hardware: 3/8th inch - 16 thread
• Includes two Camera Head Mount Plates and Basket as shown
-Accessory shelf for notebook is available as option
Studio Titan reserves the right to make product changes and improvements as required. As a result, the product supplied may not be exactly as pictured or specified.
This product is intended for use by professional and commercial photographers in a studio environment with a high ceiling. The wheels are designed to be used indoors on a floor that is smooth, hard, flat and unobstructed. It is designed to be used at all times with a load (Camera or laptop shelf or both). This product is not recommended for use by hobbyists or in a household environment with a low ceiling or carpeted floors. Carpeting or pitted surfaces are not recommended because of the increased rolling resistance which can cause the stand to tip over. If the surface is not ideal, the stand must be moved with caution, very slowly, using both hands one at the top and the other at the bottom to steady the stand in order to prevent the stand from tipping over. If the surface is not ideal, lower the load to the waist level before moving the stand. We also recommend the use of a sandbag or weight attached at the base when conditions are not ideal to prevent tipping over. Ultimately it’s the users' responsibility to understand how the stand operates and to use the stand within its specification limits, as intended, to ensure their own safety and the safety of their equipment. It is also recommended to use a short tether cable to secure the camera to the stand in the event that the head, head plate or camera adapter plate comes loose or fails. Some assembly is required, we recommend using an assistant during the initial product assembly.
Assembly Instructions are inside the package. If the assembly instructions are missing or you do not fully understand the instructions stop the assembly and consider the following resources. Visit the “SETUP” area of the website for documentation. Email questions to STA or contact STA by phone for further assistance.
The Vertical and Horizontal columns are made of aluminum. The counterweight is S20C steel.
The nuts and bolts are made of steel. The casters are polyurethane. This product does not contain lead.
Note: Due to this products large size and specific packaging and handling requirements it is sold as "non returnable".